HOW TO SET UP A TUB YOURSELF

How to Set up a Tub Yourself

How to Set up a Tub Yourself

Blog Article

Visit My Website

Just how do you feel with regards to Installing A Bathtub?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Setting up a tub isn't precisely rocket science, but it does need strong plumbing, woodworking, and also sometimes, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably difficult task. If the old tub is readily accessible, the project can move rapidly; if you have to open a wall to remove the old tub and position the new tub, the job is a lot harder. In either case, the project is within a home handyman's abilities, although you will require a helper to vacate the old bathtub and also embeded in the brand-new one. Make sure you have actually qualified yourself for the work and are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed job, it is much better to think about employing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you install a brand-new tub in your shower room if you have already bought a new bathtub as well as don't need to transform the setup of your previous water system pipes.
Your devices as well as material checklist ought to comprise the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Preparing for the Setup


    Firstly, the sustaining framework provided with the bathroom should be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets unit to stop strain on the tub.
    Fit the flexible faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the supplied washing machines.
    Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its last placement.

    Removing Old Taps


    If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you must do is separate the supply of water. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of eliminating the existing faucets can be fairly bothersome as a result of the limited accessibility that is often the case.
    Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. When the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
    Prior to going on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.

    Setting up the Tub


    Utilizing the two wooden boards under its feet, position the bathtub in the required position. The wood boards are useful in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
    The next objective is to make sure that the bathtub is leveled all round. This can be attained by examining the level and adjusting the feet on the bath tub till the level reviews degree.
    To set up taps, fit the bottom of the outermost adaptable faucet port to the suitable supply pipe by making a compression join; then do the very same for the other faucet.
    Activate the water system as well as check all joints and also brand-new pipework for leaks and tighten them if necessary. Load the tub and additionally examine the overflow outlet and the regular electrical outlet for leaks.
    Finally, take care of the bath paneling as described in the supplier's instruction manual. Tiling and securing around the bathtub should wait until the bath tub has actually been made use of at the very least when as this will certainly resolve it into its final position.

    Fitting New Taps


    If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and the other end supplies a connection to the existent supply pipes.
    If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
    Next off, position the faucet in the installing hole in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the supplier offered backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former kind ought to be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bath tub


    In the area where the bath satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with wetness as well as possible leakages to the ceiling below.
    You can select from a range of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes and also cartridges, and are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to enable the activity experienced when the tub remains in use. The sealant can fracture relatively early if you do not take into account this movement prior to securing.
    Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the market. It is a good idea to fit the floor tiles using water-resistant or water-proof glue and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    As an enthusiastic person who reads on A Step-by-Step Guide to Installing a Bathtub, I was thinking sharing that piece of writing was a smart idea. Be sure to take the time to distribute this blog post if you enjoyed it. I praise you for your time. Don't forget to come visit our blog back soon.




    Book Instantly


    Report this page